Residual performance of a silyl-modified polymer adhesive for CFRP-steel interface exposed to thermally-induced stress states

Yail J. Kim, Seung Won Hyun, Isamu Yoshitake, Jae Yoon Kang

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

This paper presents an experimental program evaluating the residual behavior of carbon fiber reinforced polymer (CFRP)-steel interface bonded with a silyl-modified polymer (SMP) adhesive when subjected to thermally-induced stress states. A total of 40 specimens are prepared and exposed to elevated temperatures from 25 °C to 200 °C. According to test results, interfacial capacity is well maintained up to a temperature of 100 °C; however, thermal hysteresis takes place beyond 100 °C. Exposure temperatures higher than 175 °C result in a phase-transition of the adhesive morphology during heating and influence the adhesion characteristics of the bonding agent. Geometric discontinuities along the interface affect CFRP-strain development and a shear-lag mechanism is noticed, which is virtually independent of the degree of thermal exposure. Fiber disintegration is the primary failure mode of the interface up to 150 °C, including intricate local fiber dislocation and partial CFRP pull-out. The specimens exposed to temperatures higher than 175 °C revealed a simple CFRP-debonding failure mode due to the thermal damage of the SMP. A probabilistic approach is taken to complement the experimental observation. The probability of the CFRP-steel interface tested is found to be normally distributed. The Bayesian updating method probabilistically infers the thermal characteristics of the interface with emphasis on temperature-dependent interfacial fracture energy. Design properties are proposed for practical application of the CFRP-steel interface with SMP.

Original languageEnglish (US)
Pages (from-to)117-127
Number of pages11
JournalInternational Journal of Adhesion and Adhesives
Volume51
DOIs
StatePublished - Jun 2014

Fingerprint

Steel
Carbon fibers
Adhesives
Polymers
Failure modes
Temperature
carbon fiber
Fracture energy
Fibers
Disintegration
Debonding
Hysteresis
Adhesion
Phase transitions
Heating
Hot Temperature

Keywords

  • Carbon fiber reinforced polymer (CFRP)
  • Deterioration
  • Interface
  • Silyl-modified polymer (SMP)
  • Steel
  • Temperature

ASJC Scopus subject areas

  • Biomaterials
  • Chemical Engineering(all)
  • Polymers and Plastics

Cite this

Residual performance of a silyl-modified polymer adhesive for CFRP-steel interface exposed to thermally-induced stress states. / Kim, Yail J.; Hyun, Seung Won; Yoshitake, Isamu; Kang, Jae Yoon.

In: International Journal of Adhesion and Adhesives, Vol. 51, 06.2014, p. 117-127.

Research output: Contribution to journalArticle

@article{d1aea5f85c84416184a356cadfad9b54,
title = "Residual performance of a silyl-modified polymer adhesive for CFRP-steel interface exposed to thermally-induced stress states",
abstract = "This paper presents an experimental program evaluating the residual behavior of carbon fiber reinforced polymer (CFRP)-steel interface bonded with a silyl-modified polymer (SMP) adhesive when subjected to thermally-induced stress states. A total of 40 specimens are prepared and exposed to elevated temperatures from 25 °C to 200 °C. According to test results, interfacial capacity is well maintained up to a temperature of 100 °C; however, thermal hysteresis takes place beyond 100 °C. Exposure temperatures higher than 175 °C result in a phase-transition of the adhesive morphology during heating and influence the adhesion characteristics of the bonding agent. Geometric discontinuities along the interface affect CFRP-strain development and a shear-lag mechanism is noticed, which is virtually independent of the degree of thermal exposure. Fiber disintegration is the primary failure mode of the interface up to 150 °C, including intricate local fiber dislocation and partial CFRP pull-out. The specimens exposed to temperatures higher than 175 °C revealed a simple CFRP-debonding failure mode due to the thermal damage of the SMP. A probabilistic approach is taken to complement the experimental observation. The probability of the CFRP-steel interface tested is found to be normally distributed. The Bayesian updating method probabilistically infers the thermal characteristics of the interface with emphasis on temperature-dependent interfacial fracture energy. Design properties are proposed for practical application of the CFRP-steel interface with SMP.",
keywords = "Carbon fiber reinforced polymer (CFRP), Deterioration, Interface, Silyl-modified polymer (SMP), Steel, Temperature",
author = "Kim, {Yail J.} and Hyun, {Seung Won} and Isamu Yoshitake and Kang, {Jae Yoon}",
year = "2014",
month = "6",
doi = "10.1016/j.ijadhadh.2014.03.003",
language = "English (US)",
volume = "51",
pages = "117--127",
journal = "International Journal of Adhesion and Adhesives",
issn = "0143-7496",
publisher = "Elsevier Limited",

}

TY - JOUR

T1 - Residual performance of a silyl-modified polymer adhesive for CFRP-steel interface exposed to thermally-induced stress states

AU - Kim, Yail J.

AU - Hyun, Seung Won

AU - Yoshitake, Isamu

AU - Kang, Jae Yoon

PY - 2014/6

Y1 - 2014/6

N2 - This paper presents an experimental program evaluating the residual behavior of carbon fiber reinforced polymer (CFRP)-steel interface bonded with a silyl-modified polymer (SMP) adhesive when subjected to thermally-induced stress states. A total of 40 specimens are prepared and exposed to elevated temperatures from 25 °C to 200 °C. According to test results, interfacial capacity is well maintained up to a temperature of 100 °C; however, thermal hysteresis takes place beyond 100 °C. Exposure temperatures higher than 175 °C result in a phase-transition of the adhesive morphology during heating and influence the adhesion characteristics of the bonding agent. Geometric discontinuities along the interface affect CFRP-strain development and a shear-lag mechanism is noticed, which is virtually independent of the degree of thermal exposure. Fiber disintegration is the primary failure mode of the interface up to 150 °C, including intricate local fiber dislocation and partial CFRP pull-out. The specimens exposed to temperatures higher than 175 °C revealed a simple CFRP-debonding failure mode due to the thermal damage of the SMP. A probabilistic approach is taken to complement the experimental observation. The probability of the CFRP-steel interface tested is found to be normally distributed. The Bayesian updating method probabilistically infers the thermal characteristics of the interface with emphasis on temperature-dependent interfacial fracture energy. Design properties are proposed for practical application of the CFRP-steel interface with SMP.

AB - This paper presents an experimental program evaluating the residual behavior of carbon fiber reinforced polymer (CFRP)-steel interface bonded with a silyl-modified polymer (SMP) adhesive when subjected to thermally-induced stress states. A total of 40 specimens are prepared and exposed to elevated temperatures from 25 °C to 200 °C. According to test results, interfacial capacity is well maintained up to a temperature of 100 °C; however, thermal hysteresis takes place beyond 100 °C. Exposure temperatures higher than 175 °C result in a phase-transition of the adhesive morphology during heating and influence the adhesion characteristics of the bonding agent. Geometric discontinuities along the interface affect CFRP-strain development and a shear-lag mechanism is noticed, which is virtually independent of the degree of thermal exposure. Fiber disintegration is the primary failure mode of the interface up to 150 °C, including intricate local fiber dislocation and partial CFRP pull-out. The specimens exposed to temperatures higher than 175 °C revealed a simple CFRP-debonding failure mode due to the thermal damage of the SMP. A probabilistic approach is taken to complement the experimental observation. The probability of the CFRP-steel interface tested is found to be normally distributed. The Bayesian updating method probabilistically infers the thermal characteristics of the interface with emphasis on temperature-dependent interfacial fracture energy. Design properties are proposed for practical application of the CFRP-steel interface with SMP.

KW - Carbon fiber reinforced polymer (CFRP)

KW - Deterioration

KW - Interface

KW - Silyl-modified polymer (SMP)

KW - Steel

KW - Temperature

UR - http://www.scopus.com/inward/record.url?scp=84897470528&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84897470528&partnerID=8YFLogxK

U2 - 10.1016/j.ijadhadh.2014.03.003

DO - 10.1016/j.ijadhadh.2014.03.003

M3 - Article

AN - SCOPUS:84897470528

VL - 51

SP - 117

EP - 127

JO - International Journal of Adhesion and Adhesives

JF - International Journal of Adhesion and Adhesives

SN - 0143-7496

ER -