Multi-quadrant surgical robot for single incision laparoscopic colectomy

E. J. Markvicka, R. L. McCormick, T. P. Frederick, J. R. Bartels, Shane M Farritor, Dmitry Oleynikov

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Colorectal surgery is an area of active research within general surgery. However, over 80% of these procedures currently require an open surgery based on the size and location of the tumor. The current state-of-the-art surgical instruments are unintuitive, restricted by the incision site, and often require timely repositioning tasks during complex surgical procedures. A multi-quadrant miniature in vivo surgical robot has been developed to mitigate these limitations as well as the invasiveness of colorectal procedures. By reducing invasiveness, the patient benefits from improved cosmetics, decreased postoperative pain, faster recovery time, and reduced financial burden. A paradigm shift in invasiveness is often inversely proportional to surgeon benefits. Yet, through the use of a robotic device, the surgeon benefits from improved ergonomics, intuitive control, and fewer required repositioning tasks. This paper presents a two armed robotic device that can be controlled from a remote surgical interface. Each arm has six internally actuated degrees of freedom, decoupling the system from the incision site. Each arm is also equipped with a specialized interchangeable end effector. For the surgical procedure, visual feedback is provided through the use of a standard laparoscope with incorporated light source. The robotic device is introduced into the abdominal cavity through a hand-assisted laparoscopic surgery (HALS) port that is placed within the navel. The device is then grossly positioned to the site of interest within the abdominal cavity through the use of a protruding rod that is rigidly attached to each arm. The surgeon can then begin to manipulate tissue through the use of the surgical interface that is remotely located within the operating room. This interface is comprised of a monitor to provide visual feedback, foot pedals to control the operational state of the device, and two haptic devices to control the end point location of each arm and state of the end effectors.

Original languageEnglish (US)
Title of host publication37th Mechanisms and Robotics Conference
PublisherAmerican Society of Mechanical Engineers
ISBN (Print)9780791855935
DOIs
StatePublished - Jan 1 2013
EventASME 2013 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, IDETC/CIE 2013 - Portland, OR, United States
Duration: Aug 4 2013Aug 7 2013

Publication series

NameProceedings of the ASME Design Engineering Technical Conference
Volume6 A

Conference

ConferenceASME 2013 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, IDETC/CIE 2013
CountryUnited States
CityPortland, OR
Period8/4/138/7/13

Fingerprint

Quadrant
Surgery
Robot
Robotics
End effectors
Laparoscopy
Feedback
Operating rooms
Cavity
Postoperative Pain
Cosmetics
Haptic Device
Ergonomics
Point Location
Light sources
Tumors
End point
Decoupling
Tissue
Intuitive

ASJC Scopus subject areas

  • Modeling and Simulation
  • Mechanical Engineering
  • Computer Science Applications
  • Computer Graphics and Computer-Aided Design

Cite this

Markvicka, E. J., McCormick, R. L., Frederick, T. P., Bartels, J. R., Farritor, S. M., & Oleynikov, D. (2013). Multi-quadrant surgical robot for single incision laparoscopic colectomy. In 37th Mechanisms and Robotics Conference [V06AT07A013] (Proceedings of the ASME Design Engineering Technical Conference; Vol. 6 A). American Society of Mechanical Engineers. https://doi.org/10.1115/DETC2013-13161

Multi-quadrant surgical robot for single incision laparoscopic colectomy. / Markvicka, E. J.; McCormick, R. L.; Frederick, T. P.; Bartels, J. R.; Farritor, Shane M; Oleynikov, Dmitry.

37th Mechanisms and Robotics Conference. American Society of Mechanical Engineers, 2013. V06AT07A013 (Proceedings of the ASME Design Engineering Technical Conference; Vol. 6 A).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Markvicka, EJ, McCormick, RL, Frederick, TP, Bartels, JR, Farritor, SM & Oleynikov, D 2013, Multi-quadrant surgical robot for single incision laparoscopic colectomy. in 37th Mechanisms and Robotics Conference., V06AT07A013, Proceedings of the ASME Design Engineering Technical Conference, vol. 6 A, American Society of Mechanical Engineers, ASME 2013 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, IDETC/CIE 2013, Portland, OR, United States, 8/4/13. https://doi.org/10.1115/DETC2013-13161
Markvicka EJ, McCormick RL, Frederick TP, Bartels JR, Farritor SM, Oleynikov D. Multi-quadrant surgical robot for single incision laparoscopic colectomy. In 37th Mechanisms and Robotics Conference. American Society of Mechanical Engineers. 2013. V06AT07A013. (Proceedings of the ASME Design Engineering Technical Conference). https://doi.org/10.1115/DETC2013-13161
Markvicka, E. J. ; McCormick, R. L. ; Frederick, T. P. ; Bartels, J. R. ; Farritor, Shane M ; Oleynikov, Dmitry. / Multi-quadrant surgical robot for single incision laparoscopic colectomy. 37th Mechanisms and Robotics Conference. American Society of Mechanical Engineers, 2013. (Proceedings of the ASME Design Engineering Technical Conference).
@inproceedings{1b4bb6cc276a40fcba9be9a96a175745,
title = "Multi-quadrant surgical robot for single incision laparoscopic colectomy",
abstract = "Colorectal surgery is an area of active research within general surgery. However, over 80{\%} of these procedures currently require an open surgery based on the size and location of the tumor. The current state-of-the-art surgical instruments are unintuitive, restricted by the incision site, and often require timely repositioning tasks during complex surgical procedures. A multi-quadrant miniature in vivo surgical robot has been developed to mitigate these limitations as well as the invasiveness of colorectal procedures. By reducing invasiveness, the patient benefits from improved cosmetics, decreased postoperative pain, faster recovery time, and reduced financial burden. A paradigm shift in invasiveness is often inversely proportional to surgeon benefits. Yet, through the use of a robotic device, the surgeon benefits from improved ergonomics, intuitive control, and fewer required repositioning tasks. This paper presents a two armed robotic device that can be controlled from a remote surgical interface. Each arm has six internally actuated degrees of freedom, decoupling the system from the incision site. Each arm is also equipped with a specialized interchangeable end effector. For the surgical procedure, visual feedback is provided through the use of a standard laparoscope with incorporated light source. The robotic device is introduced into the abdominal cavity through a hand-assisted laparoscopic surgery (HALS) port that is placed within the navel. The device is then grossly positioned to the site of interest within the abdominal cavity through the use of a protruding rod that is rigidly attached to each arm. The surgeon can then begin to manipulate tissue through the use of the surgical interface that is remotely located within the operating room. This interface is comprised of a monitor to provide visual feedback, foot pedals to control the operational state of the device, and two haptic devices to control the end point location of each arm and state of the end effectors.",
author = "Markvicka, {E. J.} and McCormick, {R. L.} and Frederick, {T. P.} and Bartels, {J. R.} and Farritor, {Shane M} and Dmitry Oleynikov",
year = "2013",
month = "1",
day = "1",
doi = "10.1115/DETC2013-13161",
language = "English (US)",
isbn = "9780791855935",
series = "Proceedings of the ASME Design Engineering Technical Conference",
publisher = "American Society of Mechanical Engineers",
booktitle = "37th Mechanisms and Robotics Conference",

}

TY - GEN

T1 - Multi-quadrant surgical robot for single incision laparoscopic colectomy

AU - Markvicka, E. J.

AU - McCormick, R. L.

AU - Frederick, T. P.

AU - Bartels, J. R.

AU - Farritor, Shane M

AU - Oleynikov, Dmitry

PY - 2013/1/1

Y1 - 2013/1/1

N2 - Colorectal surgery is an area of active research within general surgery. However, over 80% of these procedures currently require an open surgery based on the size and location of the tumor. The current state-of-the-art surgical instruments are unintuitive, restricted by the incision site, and often require timely repositioning tasks during complex surgical procedures. A multi-quadrant miniature in vivo surgical robot has been developed to mitigate these limitations as well as the invasiveness of colorectal procedures. By reducing invasiveness, the patient benefits from improved cosmetics, decreased postoperative pain, faster recovery time, and reduced financial burden. A paradigm shift in invasiveness is often inversely proportional to surgeon benefits. Yet, through the use of a robotic device, the surgeon benefits from improved ergonomics, intuitive control, and fewer required repositioning tasks. This paper presents a two armed robotic device that can be controlled from a remote surgical interface. Each arm has six internally actuated degrees of freedom, decoupling the system from the incision site. Each arm is also equipped with a specialized interchangeable end effector. For the surgical procedure, visual feedback is provided through the use of a standard laparoscope with incorporated light source. The robotic device is introduced into the abdominal cavity through a hand-assisted laparoscopic surgery (HALS) port that is placed within the navel. The device is then grossly positioned to the site of interest within the abdominal cavity through the use of a protruding rod that is rigidly attached to each arm. The surgeon can then begin to manipulate tissue through the use of the surgical interface that is remotely located within the operating room. This interface is comprised of a monitor to provide visual feedback, foot pedals to control the operational state of the device, and two haptic devices to control the end point location of each arm and state of the end effectors.

AB - Colorectal surgery is an area of active research within general surgery. However, over 80% of these procedures currently require an open surgery based on the size and location of the tumor. The current state-of-the-art surgical instruments are unintuitive, restricted by the incision site, and often require timely repositioning tasks during complex surgical procedures. A multi-quadrant miniature in vivo surgical robot has been developed to mitigate these limitations as well as the invasiveness of colorectal procedures. By reducing invasiveness, the patient benefits from improved cosmetics, decreased postoperative pain, faster recovery time, and reduced financial burden. A paradigm shift in invasiveness is often inversely proportional to surgeon benefits. Yet, through the use of a robotic device, the surgeon benefits from improved ergonomics, intuitive control, and fewer required repositioning tasks. This paper presents a two armed robotic device that can be controlled from a remote surgical interface. Each arm has six internally actuated degrees of freedom, decoupling the system from the incision site. Each arm is also equipped with a specialized interchangeable end effector. For the surgical procedure, visual feedback is provided through the use of a standard laparoscope with incorporated light source. The robotic device is introduced into the abdominal cavity through a hand-assisted laparoscopic surgery (HALS) port that is placed within the navel. The device is then grossly positioned to the site of interest within the abdominal cavity through the use of a protruding rod that is rigidly attached to each arm. The surgeon can then begin to manipulate tissue through the use of the surgical interface that is remotely located within the operating room. This interface is comprised of a monitor to provide visual feedback, foot pedals to control the operational state of the device, and two haptic devices to control the end point location of each arm and state of the end effectors.

UR - http://www.scopus.com/inward/record.url?scp=84896993199&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84896993199&partnerID=8YFLogxK

U2 - 10.1115/DETC2013-13161

DO - 10.1115/DETC2013-13161

M3 - Conference contribution

AN - SCOPUS:84896993199

SN - 9780791855935

T3 - Proceedings of the ASME Design Engineering Technical Conference

BT - 37th Mechanisms and Robotics Conference

PB - American Society of Mechanical Engineers

ER -