Experimental study of micro ultrasonic machining process

Sreenidhi Cherku, Murali M. Sundaram, K. P. Rajurkar

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

This paper presents the results of micro ultrasonic machining using oil based abrasive slurry. An in-house built experimental setup was used to conduct designed experiments. The influence of process parameters such as slurry medium, slurry concentration, and abrasive particle size on the performance of micro USM Material Removal Rate (MRR) and Surface Roughness (SR) is reported. It is evident from the experimental study that machining with water based slurry is suitable only for finer particles sizes with higher concentration or medium particles sizes with medium concentration or coarser particle sizes with lower particles where as machining with oil based slurry is always suitable for all the particle sizes with low concentration. Further the study reveals that machining with oil based slurry gives good surface finish compared to the water based slurry. Good surface finish is given by machining with the finer particles whereas machining with coarser grains gives poor surface finish.

Original languageEnglish (US)
Title of host publicationProceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE
StatePublished - Dec 1 2008
Event23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE - Portland, OR, United States
Duration: Oct 19 2008Oct 24 2008

Publication series

NameProceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE

Conference

Conference23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE
CountryUnited States
CityPortland, OR
Period10/19/0810/24/08

Fingerprint

Machining
Ultrasonics
Particle size
Abrasives
Water
Surface roughness
Oils
Experiments

ASJC Scopus subject areas

  • Mechanical Engineering

Cite this

Cherku, S., Sundaram, M. M., & Rajurkar, K. P. (2008). Experimental study of micro ultrasonic machining process. In Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE (Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE).

Experimental study of micro ultrasonic machining process. / Cherku, Sreenidhi; Sundaram, Murali M.; Rajurkar, K. P.

Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE. 2008. (Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Cherku, S, Sundaram, MM & Rajurkar, KP 2008, Experimental study of micro ultrasonic machining process. in Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE. Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE, 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE, Portland, OR, United States, 10/19/08.
Cherku S, Sundaram MM, Rajurkar KP. Experimental study of micro ultrasonic machining process. In Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE. 2008. (Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE).
Cherku, Sreenidhi ; Sundaram, Murali M. ; Rajurkar, K. P. / Experimental study of micro ultrasonic machining process. Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE. 2008. (Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE).
@inproceedings{a467c90d5fe24323b749a72d3c43b8d4,
title = "Experimental study of micro ultrasonic machining process",
abstract = "This paper presents the results of micro ultrasonic machining using oil based abrasive slurry. An in-house built experimental setup was used to conduct designed experiments. The influence of process parameters such as slurry medium, slurry concentration, and abrasive particle size on the performance of micro USM Material Removal Rate (MRR) and Surface Roughness (SR) is reported. It is evident from the experimental study that machining with water based slurry is suitable only for finer particles sizes with higher concentration or medium particles sizes with medium concentration or coarser particle sizes with lower particles where as machining with oil based slurry is always suitable for all the particle sizes with low concentration. Further the study reveals that machining with oil based slurry gives good surface finish compared to the water based slurry. Good surface finish is given by machining with the finer particles whereas machining with coarser grains gives poor surface finish.",
author = "Sreenidhi Cherku and Sundaram, {Murali M.} and Rajurkar, {K. P.}",
year = "2008",
month = "12",
day = "1",
language = "English (US)",
isbn = "9781887706483",
series = "Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE",
booktitle = "Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE",

}

TY - GEN

T1 - Experimental study of micro ultrasonic machining process

AU - Cherku, Sreenidhi

AU - Sundaram, Murali M.

AU - Rajurkar, K. P.

PY - 2008/12/1

Y1 - 2008/12/1

N2 - This paper presents the results of micro ultrasonic machining using oil based abrasive slurry. An in-house built experimental setup was used to conduct designed experiments. The influence of process parameters such as slurry medium, slurry concentration, and abrasive particle size on the performance of micro USM Material Removal Rate (MRR) and Surface Roughness (SR) is reported. It is evident from the experimental study that machining with water based slurry is suitable only for finer particles sizes with higher concentration or medium particles sizes with medium concentration or coarser particle sizes with lower particles where as machining with oil based slurry is always suitable for all the particle sizes with low concentration. Further the study reveals that machining with oil based slurry gives good surface finish compared to the water based slurry. Good surface finish is given by machining with the finer particles whereas machining with coarser grains gives poor surface finish.

AB - This paper presents the results of micro ultrasonic machining using oil based abrasive slurry. An in-house built experimental setup was used to conduct designed experiments. The influence of process parameters such as slurry medium, slurry concentration, and abrasive particle size on the performance of micro USM Material Removal Rate (MRR) and Surface Roughness (SR) is reported. It is evident from the experimental study that machining with water based slurry is suitable only for finer particles sizes with higher concentration or medium particles sizes with medium concentration or coarser particle sizes with lower particles where as machining with oil based slurry is always suitable for all the particle sizes with low concentration. Further the study reveals that machining with oil based slurry gives good surface finish compared to the water based slurry. Good surface finish is given by machining with the finer particles whereas machining with coarser grains gives poor surface finish.

UR - http://www.scopus.com/inward/record.url?scp=84884932704&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84884932704&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:84884932704

SN - 9781887706483

T3 - Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE

BT - Proceedings of the 23rd Annual Meeting of the American Society for Precision Engineering, ASPE 2008 and the 12th ICPE

ER -